The Application of Hole Drilling Method Integrated with 2D and 3D Digital Image Correlation for Estimating Residual Stresses

Sulaiman S. Arif; Zaid S. Hammoudi

doi:10.29194/NJES.29030508

Authors

Sulaiman S. Arif Department of Mechanical Engineering, University of Diyala, 32001 Diyala-Iraq.
Zaid S. Hammoudi Department of Mechanical Engineering, University of Diyala, 32001 Diyala-Iraq.

DOI:

https://doi.org/10.29194/NJES.29030508

Keywords:

Digital Image Correlation, Residual Stresses, Hole Drilling Method, Finite Element Analysis

Abstract

Accurate measurement of residual stress is crucial for assessing structural integrity and predicting fatigue life. Although significant work has been documented on applying two-dimensional (2D) and three-dimensional (3D) digital image correlation (DIC) independently to the hole drilling process, a direct comparison of their accuracy and performance under the same conditions (most importantly, with plastic deformation) has not yet been published. This work conducted the first explicit comparison between 2D and 3D-DIC combined with the hole drilling method for residual stress measurement using finite element (FE) analysis as a validation standard. Residual stresses were induced through plastic bending of a square beam made of aluminum alloy 7075-T651. The findings indicate that the 3D-DIC is more accurate (93%) compared to the 2D-DIC (88%), objectively tested against FE solutions, even on a flat surface, which is theoretically ideal for 2D-DIC.This difference in accuracy is attributed to the higher sensitivity of the 2D-DIC to out-of-plane deformation and camera misalignment. These results support the effectiveness of 3D-DIC in measuring residual stress and explain that there is a trade-off between the practical accuracy of 2D and 3D versions of the hole-drilling technique.

Downloads

Download data is not yet available.

Author Biography

Zaid S. Hammoudi, Department of Mechanical Engineering, University of Diyala, 32001 Diyala-Iraq.

mechanical engineering department

References

G. E. Totten, M. A. H. Howes, and T. Inoue, *Handbook of Residual Stress and Deformation of Steel*. ASM Int., 2002.

X. Li, Y. Zhang, H. Wang, and L. Chen, "Research progress of residual stress measurement methods," Elsevier Ltd., Apr. 2024. https://doi.org/10.1016/j.heliyon.2024.e28348 DOI: https://doi.org/10.1016/j.heliyon.2024.e28348

N. S. Rossini, M. Dassisti, K. Y. Benyounis, and A. G. Olabi, "Methods of measuring residual stresses in components," Mater. Des., Mar. 2012. https://doi.org/10.1016/j.matdes.2011.08.022 DOI: https://doi.org/10.1016/j.matdes.2011.08.022

M. Ya, D. Fulong, X. Huimin, and J. Lli, "Measurement of non-uniform residual stresses by combined moiré interferometry and hole-drilling method: theory, experimental method and applications," Chin. J. Mech., vol. 19, no. 6, 2003. https://doi.org/10.1007/BF02484550 DOI: https://doi.org/10.1007/BF02484550

V. S. Pisarev, M. M. Bondarenko, A. V. Chernov, and A. N. Vinogradova, "General approach to residual stresses determination in thin-walled structures by combining the hole drilling method and reflection hologram interferometry," Int. J. Mech. Sci., vol. 47, no. 9, pp. 1350-1376, Sep. 2005. https://doi.org/10.1016/j.ijmecsci.2005.05.002 DOI: https://doi.org/10.1016/j.ijmecsci.2005.05.002

D. V. Nelson, A. Makino, and T. Schmidt, "Residual stress determination using hole drilling and 3D image correlation," Exp. Mech., vol. 46, no. 1, pp. 31-38, Feb. 2006. https://doi.org/10.1007/s11340-006-5859-0 DOI: https://doi.org/10.1007/s11340-006-5859-0

J. D. Lord, D. Penn, and P. Whitehead, "The application of digital image correlation for measuring residual stress by incremental hole drilling," in *Appl. Mech. Mater.*, Trans Tech Publ., 2008, pp. 65-73. https://doi.org/10.4028/www.scientific.net/AMM.13-14.65 DOI: https://doi.org/10.4028/www.scientific.net/AMM.13-14.65

Y. H. Chen, X. Chen, N. Xu, and L. Yang, "The digital image correlation technique applied to hole drilling residual stress measurement," in *SAE Tech. Papers*, SAE Int., 2014. https://doi.org/10.4271/2014-01-0825 DOI: https://doi.org/10.4271/2014-01-0825

T. Brynk and B. Romelczyk-Baishya, "Residual stress estimation based on 3D DIC displacement field measurement around drilled holes," in *Procedia Struct. Integr.*, Elsevier, 2018, pp. 1267-1272. https://doi.org/10.1016/j.prostr.2018.12.259

Y. Peng, J. Zhao, L. S. Chen, and J. Dong, "Residual stress measurement combining blind-hole drilling and digital image correlation approach," J. Constr. Steel Res., vol. 176, Jan. 2021. https://doi.org/10.1016/j.jcsr.2020.106346 DOI: https://doi.org/10.1016/j.jcsr.2020.106346

R. Blödorn, L. A. Bonomo, M. R. Viotti, R. B. Schroeter, and A. Albertazzi, "Calibration coefficients determination through FEM simulations for the hole-drilling method considering the real hole geometry," Exp. Tech., vol. 41, no. 1, pp. 37-44, Jan. 2017. https://doi.org/10.1007/s40799-016-0152-3 DOI: https://doi.org/10.1007/s40799-016-0152-3

J. M. Alegre, A. Díaz, I. I. Cuesta, and J. M. Manso, "Analysis of the influence of the thickness and the hole radius on the calibration coefficients in the hole-drilling method for the determination of non-uniform residual stresses," Exp. Mech., vol. 59, no. 1, pp. 79-94, Jan. 2019. https://doi.org/10.1007/s11340-018-0433-0 DOI: https://doi.org/10.1007/s11340-018-0433-0

D. Halabuk and T. Návrat, "Determination of residual stresses in cylindrical components by the hole-drilling method," Exp. Mech., vol. 62, no. 1, pp. 87-99, Jan. 2022. https://doi.org/10.1007/s11340-021-00765-y DOI: https://doi.org/10.1007/s11340-021-00765-y

M. C. Lakey and M. R. Hill, "Validation of hole-drilling residual stress measurements in workpieces of various thickness," Exp. Mech., Nov. 2024. https://doi.org/10.1007/s11340-024-01107-4 DOI: https://doi.org/10.1007/s11340-024-01107-4

M. Hagara, F. Trebuňa, M. Pástor, R. Huňady, and P. Lengvarský, "Analysis of the aspects of residual stresses quantification performed by 3D DIC combined with standardized hole-drilling method," Measurement, vol. 137, pp. 238-256, Apr. 2019. https://doi.org/10.1016/j.measurement.2019.01.028 DOI: https://doi.org/10.1016/j.measurement.2019.01.028

O. Yuksel, I. Baran, N. Ersoy, and R. Akkerman, "Investigation of transverse residual stresses in a thick pultruded composite using digital image correlation with hole drilling," Compos. Struct., vol. 223, Sep. 2019. https://doi.org/10.1016/j.compstruct.2019.110954 DOI: https://doi.org/10.1016/j.compstruct.2019.110954

T. Brynk and B. Romelczyk-Baishya, "Residual stress estimation based on 3D DIC displacement field measurement around drilled holes," in *Procedia Struct. Integr.*, Elsevier, 2018, pp. 1267-1272. https://doi.org/10.1016/j.prostr.2018.12.259 DOI: https://doi.org/10.1016/j.prostr.2018.12.259

F. J. Corrêa, F. A. Jahnert, and J. P. Tomás, "Residual stress profile determination by the hole-drilling method with calibration coefficients obtained using FEM," J. Theor. Appl. Mech. (Poland), vol. 59, no. 4, pp. 661-673, 2021. https://doi.org/10.15632/jtam-pl/141686 DOI: https://doi.org/10.15632/jtam-pl/141686

A. Chatterjee, A. Mandal, and A. Giri, "A study on residual stress measurement by DIC approach in FSW welded AA6082 joints," in *Procedia Struct. Integr.*, Elsevier, 2024, pp. 13-19. https://doi.org/10.1016/j.prostr.2024.05.027 DOI: https://doi.org/10.1016/j.prostr.2024.05.027

ASTM Int., "Test method for determining residual stresses by the hole-drilling strain-gage method," West Conshohocken, PA, Apr. 2013.