Functionally Graded Materials of Stainless Steel 316L-Inconel 625: Optimization of the study characteristics through Porosity, Microstructure, and Mechanical Performance
DOI:
https://doi.org/10.29194/NJES.29020291Keywords:
Additive Manufacturing, Laser Directed Energy Deposition (LDED) technique, Gradient Metallurgy, Functionally Graded Material (FGM), SS316L/IN625 alloys, Microstructural Texture EvolutionAbstract
Functionally graded materials were created using laser-directed energy deposition technology. This work examines how different mixing ratios of Stainless Steel 316L and Inconel 625 affect the relative density and porosity of these materials. Twelve samples were created using a constant laser power of 600 W, three different laser scan speeds (20, 25, and 30 mm/s), and four different SS316L/IN625 transition ratios (85%/15%, 60%/40%, 40%/60%, and 15%/85%). To determine the volumetric distribution across the compositional gradients, the porosity and relative density measurements were taken. Optical and scanning electron microscopy were used for microstructural analytical characterization to differentiate between compositional gradients in grain shape and phase distribution. The mechanical performance was examined using microhardness measures, namely the Vickers method. This study applied to prove the process parameters and compositional transformations to the resulting microstructural features and mechanical properties, providing insight into optimizing the laser-directed energy deposition-manufactured functionally graded materials for advanced performance. The best graded composition was found that gives the best overall performance based on experimental data.
Downloads
References
H. R. Zareie Rajani, S. A. A. Akbari Mousavi, and F. Madani Sani, "Comparison of corrosion behavior between fusion cladded and explosive cladded Inconel 625/plain carbon steel bimetal plates," Mater. Des., vol. 43, pp. 467-474, 2013. https://doi.org/10.1016/j.matdes.2012.06.053 DOI: https://doi.org/10.1016/j.matdes.2012.06.053
K. Shah, A. Pinkerton, L. Li, and J. McGourlay, "Parametric study of development of Inconel‑steel functionally graded materials by laser direct metal deposition," Mater. Des., vol. 54, pp. 531-538, 2014. https://doi.org/10.1016/j.matdes.2013.08.079 DOI: https://doi.org/10.1016/j.matdes.2013.08.079
W. J. Sames, F. A. List, S. Pannala, R. R. Dehoff, and S. S. Babu, "The metallurgy and processing science of metal additive manufacturing," Int. Mater. Rev., vol. 61, no. 5, pp. 315-344, 2016. https://doi.org/10.1080/09506608.2015.1116649 DOI: https://doi.org/10.1080/09506608.2015.1116649
W. Li, Y. Li, Z. Li, C. Zhang, and Y. Huang, "Fabrication and characterization of a functionally graded material from Ti‑6Al‑4V to SS316 by laser metal deposition," Addit. Manuf., vol. 14, pp. 95-104, 2017. https://doi.org/10.1016/j.addma.2016.12.006 DOI: https://doi.org/10.1016/j.addma.2016.12.006
B. E. Carroll, R. R. Dehoff, S. L. Babu, and S. Pannala, "Functionally graded material of 304L stainless steel and Inconel 625 fabricated by directed energy deposition: Characterization and thermodynamic modeling," Acta Mater., vol. 108, pp. 46-54, 2016. https://doi.org/10.1016/j.actamat.2016.02.019 DOI: https://doi.org/10.1016/j.actamat.2016.02.019
R. Ghanavati, H. Naffakh‑Moosavy, M. Moradi, and M. Eshraghi, "Printability and microstructure of directed energy deposited SS316L-IN718 multi‑material: Numerical modeling and experimental analysis," Sci. Rep., vol. 12, p. 16600, 2022. https://doi.org/10.1038/s41598-022-21077-8 DOI: https://doi.org/10.1038/s41598-022-21077-8
A. Bandyopadhyay and B. Heer, "Additive manufacturing of multi‑material structures," Mater. Sci. Eng. R Rep., vol. 129, pp. 1-16, 2018. https://doi.org/10.1016/j.mser.2018.04.001 DOI: https://doi.org/10.1016/j.mser.2018.04.001
S. Hasanov, S. Alkunte, M. Rajeshirke, A. Gupta, O. Huseynov, I. Fidan, F. Alifui‑Segbaya, and A. Rennie, "Review on additive manufacturing of multi‑material parts: Progress and challenges," J. Manuf. Mater. Process., vol. 6, no. 4, 2022. https://doi.org/10.3390/jmmp6010004 DOI: https://doi.org/10.3390/jmmp6010004
C. Zhong, J. Kittel, A. Gasser, and J. H. Schleifenbaum, "Study of nickel‑based super‑alloys Inconel 718 and Inconel 625 in high‑deposition‑rate laser metal deposition," Opt. Laser Technol., vol. 109, pp. 352-360, 2019. https://doi.org/10.1016/j.optlastec.2018.08.003 DOI: https://doi.org/10.1016/j.optlastec.2018.08.003
B. Chen, Y. Zhang, H. Zhang, X. Zhang, and Y. Huang, "Development and characterization of 316L/Inconel 625 functionally graded material fabricated by laser direct metal deposition," Opt. Laser Technol., vol. 123, Art. 105916, 2019. https://doi.org/10.1016/j.optlastec.2019.105916 DOI: https://doi.org/10.1016/j.optlastec.2019.105916
A. A. Ferreira, J. P. Oliveira, A. M. P. Jesus, and F. M. Braz Fernandes, "Inconel 625/AISI 413 stainless steel functionally graded material produced by direct laser deposition," Materials, vol. 14, 2021. https://doi.org/10.3390/ma14195595 DOI: https://doi.org/10.3390/ma14195595
R. Ghanavati, H. Naffakh‑Moosavy, and M. Moradi, "Additive manufacturing of thin‑walled SS316L-IN718 functionally graded materials by direct laser metal deposition," J. Mater. Res. Technol., vol. 15, pp. 2673-2685, 2021. https://doi.org/10.1016/j.jmrt.2021.09.061 DOI: https://doi.org/10.1016/j.jmrt.2021.09.061
N. F. Jones, J. L. Beuth, and M. P. Boer, "Directed energy deposition joining of Inconel 625 to 304 stainless steel with direct bonding," J. Mater. Res., vol. 36, no. 23, pp. 5213-5225, 2021. https://doi.org/10.1557/s43578-021-00304-4 DOI: https://doi.org/10.1557/s43578-021-00304-4
H. Hotz, M. Schmidt, A. Gasser, and J. H. Schleifenbaum, "Additive manufacturing of functionally graded Ti‑Al structures by laser‑based direct energy deposition," J. Manuf. Process., vol. 68, pp. 1524-1534, 2021. https://doi.org/10.1016/j.jmapro.2021.06.068 DOI: https://doi.org/10.1016/j.jmapro.2021.06.068
R. Gotoh, K. Takahashi, T. Balamurugesan, and Y. Kondo, "Experimental and analytical investigations of AlSi10Mg, stainless steel, Inconel 625 and Ti‑6Al‑4V porous materials printed via powder bed fusion," Prog. Addit. Manuf., vol. 7, pp. 943-955, 2022. https://doi.org/10.1007/s40964-022-00269-8 DOI: https://doi.org/10.1007/s40964-022-00269-8
G. Jiang, Y. Zhang, H. Wang, X. Li, and C. Liu, "Effect of dissolved precursors on corrosion characteristics of Ni‑based alloy Inconel 625, stainless steel 316L and titanium alloy TA2 in acidic and neutral supercritical water: A comparative study," J. Supercrit. Fluids, vol. 209, Art. 106249, 2024. https://doi.org/10.1016/j.supflu.2024.106249 DOI: https://doi.org/10.1016/j.supflu.2024.106249
N. Chen, X. Zhang, Y. Li, and H. Wang, "Microstructural characteristics and crack formation in additively manufactured bimetal material of 316L stainless steel and Inconel 625," Addit. Manuf., vol. 32, Art. 101037, 2020. https://doi.org/10.1016/j.addma.2020.101037 DOI: https://doi.org/10.1016/j.addma.2020.101037
S. K. Gürel, İ. A. Yüksel, and T. O. Kılınç, "Uncertainty calculations and calibration of metal hardness testing equipment," 19th Int. Congr. Metrol., Art. 12002, 2019. https://doi.org/10.1051/metrology/201912002 DOI: https://doi.org/10.1051/metrology/201912002
D. D. Singh, S. Arjula, and A. R. Reddy, "Influence of laser power on mechanical properties of FGM of SS316L and IN625 fabricated by direct metal deposition," E3S Web Conf., vol. 552, Art. 01016, 2024. https://doi.org/10.1051/e3sconf/202455201016 DOI: https://doi.org/10.1051/e3sconf/202455201016
X. Xu, G. Mi, Y. Luo, P. Jiang, X. Shao, and C. Wang, "Morphologies, microstructures, and mechanical properties of samples produced using laser metal deposition with 316L stainless steel wire," Opt. Lasers Eng., vol. 94, pp. 1-11, 2017. https://doi.org/10.1016/j.optlaseng.2017.02.008 DOI: https://doi.org/10.1016/j.optlaseng.2017.02.008
Q. Y. Jin, Y. Li, Z. Zhang, H. Wang, and C. Liu, "Design of dissimilar material joint for defect‑free multi‑material additive manufacturing via laser‑directed energy deposition," Heliyon, vol. 10, no. 15, Art. e29666, 2024. https://doi.org/10.1016/j.heliyon.2024.e29666 DOI: https://doi.org/10.1016/j.heliyon.2024.e29666
G. Gong, J. Ye, Y. Chi, Z. Zhao, Z. Wang, G. Xia, X. Du, H. Tian, H. Yu, and C. Chen, "Research status of laser additive manufacturing for metal: A review," J. Mater. Res. Technol., vol. 15, pp. 855-884, 2021. https://doi.org/10.1016/j.jmrt.2021.08.050 DOI: https://doi.org/10.1016/j.jmrt.2021.08.050
J. K. Chaurasia, S. K. Singh, A. Kumar, and R. K. Singh, "Effect of deposition strategy and post‑processing on microstructure and mechanical properties of serviced Inconel 625 parts repaired using laser directed energy deposition," Opt. Laser Technol., vol. 168, Art. 109831, 2024. https://doi.org/10.1016/j.optlastec.2023.109831 DOI: https://doi.org/10.1016/j.optlastec.2023.109831
Z. Liu, Y. Li, H. Wang, and C. Liu, "Directed energy deposition of functional gradient material to enhance mechanical properties of heterogeneous stainless steels," Opt. Laser Technol., vol. 179, Art. 111326, 2024. https://doi.org/10.1016/j.optlastec.2024.111326 DOI: https://doi.org/10.1016/j.optlastec.2024.111326
M. G. Mouziraji, A. M. Al‑Hussein, S. Al‑Quraishi, and H. Al‑Jubouri, "A review study on metal powder materials and processing parameters in laser metal deposition," Opt. Laser Technol., vol. 170, Art. 110226, 2024. https://doi.org/10.1016/j.optlastec.2023.110226 DOI: https://doi.org/10.1016/j.optlastec.2023.110226
X. Tong, Y. Li, Z. Zhang, H. Wang, and C. Liu, "Microstructures and mechanical properties of crack‑free 316L stainless steel and Inconel 625 joint by using Laser Engineered Net Shaping," Opt. Laser Technol., vol. 155, Art. 108357, 2022. https://doi.org/10.1016/j.optlastec.2022.108357 DOI: https://doi.org/10.1016/j.optlastec.2022.108357
Y. Liu, Z. Zhang, H. Wang, and C. Liu, "Heterogeneous microstructure and tensile properties of HA188/SS316L functionally graded materials prepared by laser directed energy deposition," Opt. Laser Technol., vol. 181, Art. 111770, 2025. https://doi.org/10.1016/j.optlastec.2024.111770 DOI: https://doi.org/10.1016/j.optlastec.2024.111770
A. K. Praharaj, S. K. Singh, R. K. Singh, and J. K. Chaurasia, "Enhanced tribological performance of laser directed energy deposited Inconel 625 achieved through laser surface remelting," Surf. Coatings Technol., vol. 477, Art. 130345, 2024. https://doi.org/10.1016/j.surfcoat.2023.130345 DOI: https://doi.org/10.1016/j.surfcoat.2023.130345
M. H. Nie, Y. Li, Z. Zhang, H. Wang, and C. Liu, "Studies on the 316/NiTi functionally gradient ultra‑thick coatings fabricated with directed energy deposition: Microstructure, crystallography and wear mechanism," Appl. Surf. Sci., vol. 630, Art. 157497, 2023. https://doi.org/10.1016/j.apsusc.2023.157497 DOI: https://doi.org/10.1016/j.apsusc.2023.157497
R. Zhang, Y. Li, Z. Zhang, H. Wang, and C. Liu, "Molten pool swing in printing the steel/Inconel functionally gradient material with laser‑based directed energy deposition," Manuf. Lett., vol. 32, pp. 44-48, 2022. https://doi.org/10.1016/j.mfglet.2022.03.002 DOI: https://doi.org/10.1016/j.mfglet.2022.03.002
K. Li, Y. Li, Z. Zhang, H. Wang, and C. Liu, "A functionally graded material design from stainless steel to Ni‑based superalloy by laser metal deposition coupled with thermodynamic prediction," Mater. Des., vol. 217, Art. 110612, 2022. https://doi.org/10.1016/j.matdes.2022.110612 DOI: https://doi.org/10.1016/j.matdes.2022.110612
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Samir Ali, Ziad Taha, Barbara Previtali
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
The authors retain the copyright of their manuscript by submitting the work to this journal, and all open access articles are distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International (CC-BY-NC 4.0), which permits use for any non-commercial purpose, distribution, and reproduction in any medium, provided that the original work is properly cited.
How to Cite
